Heat Pump Installation & Services in San Marcos, СА
Repair and installation of heat pumps should be started as soon as the first operational faults are detected. Timely intervention can significantly extend the operating time in general. If any problems arise during operation, it is necessary to immediately contact professionals.
Before starting repair and installation work, masters carry out a thorough diagnosis of operability. The check is carried out with a working device: so it is possible to accurately determine the localisation of the defect. This is necessary in order to make all important measurements of parameters and see their deviations from the norm.
Regular preventive heat pump maintenance to extend the operating life
Regular preventive maintenance can significantly extend the operating life of the device. Professional performance monitoring by Accord Air in San Marcos, CA, cleaning of technical components and replacement of consumables have the best effect on the its overall functionality.
Service maintenance includes several stages of work
- Thorough external inspection. This is necessary to identify damage to the outdoor unit, as well as for the timely elimination of problems with the heating of air masses.
- Checking the pressure levels at the discharge and suction stages.
- Assessment of room heating during unit operation: detection of overheating and assessment of compressor voltage.
- Timely recording of failures. If the causes of failure are identified and remedied immediately, the operating time can be significantly extended: minor repairs can improve the situation and prevent the failure of important components.
- Regular cleaning of dirt. From time to time it is necessary to clean heat pumps from dust and dirt, which are bound to appear during the operation of the equipment.
If there are failures in the control process, the masters check the remote control, monitor the progress of commands, record the emerging failures.
Productivity of the air filters. If these components are out of order, the work of the entire system as a whole significantly deteriorates.
What you need to do to keep your heat pumps running smoothly
Repairs and installation of heat pumps periodically necessary even the most durable and productive device. Faults can occur in any technical unit, to eliminate and determine the nature of necessarily needing to contact professional masters. Their competent approach allows you to carry out the repair correctly and efficiently.
In total, the masters distinguish several common defects:
- Leakage of refrigerant. Like any climatic equipment, the heat pump operates using Freon. Leakage can be caused by mechanical damage: even the smallest scratches can lead to failure. From the very beginning, thanks to the leak detector, the masters find the vulnerable place and restore its tightness and integrity. Then the tank is re-filled with refrigerant for efficient operation of the heat pump.
- Defrosted heat exchanger. In this case, replacement or resoldering is possible. At this stage of work, specialists need to be extremely careful: it is very important to install a factory part that will meet all technical specifications. If necessary, the spare part is ordered, it is strictly forbidden to put an unsuitable version.
- Failure of the compressor. This type of repair is the most expensive – in very rare cases, the mechanism can be repaired. Most often it is necessary to install a new model, which, like the heat exchanger, must necessarily.
Additionally, if the outdoor unit is installed on the roof in direct sunlight without being covered by a specific roof, its efficiency may suffer.
All of these are effects of poor design. Any sort of heat pump’s success is reliant on expert selection and high-quality design.
Phases of heat pump upkeep
When there is a problem, maintenance is done in accordance with the following plan:
- analysis of the heat pump heating system;
- identifying the issue
- addressing the issue.
The regulations state that heat pumps must have maintenance twice a year, before the cold and before the warm seasons.
What is done for air-to-air and air-to-water heat pumps is as follows:
- examination and maintenance of the outside unit;
- checking the freon lines for leaks and system pressure (freon charge);
- checking the compressor operation;
- checking the fan;
- checking the hydraulic module,
Analysis of the performance of the automation and circuit board – the internal unit of the hydraulic module and its pumping group.
The geothermal pump checks the pressure of the geothermal field.
If it has dropped, we can talk about ethylene glycol or propylene glycol leakage underground, i.e. depressurisation.
Just like in other types of heating oil, the internal part of the hydraulic module is serviced in the geothermal one, the electronics, pump groups, etc. are checked. In general, the service of heating systems is a whole set of procedures that covers all important equipment components.
With the help of heat pump installation today it is possible to create a very reliable and efficient heating system, to create comfortable living conditions in a country house not only in summer, but also in winter, to refuse from expensive traditional energy carriers.
You can get advice on design installation and replacement of heat pumps at Accord Air in San Marcos, CA.
